Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - phil

Pages: [1] 2 3 ... 5
1
Centerfire Discussions / Re: Benchrest gunsmith canada?
« on: April 10, 2019, 08:49:07 PM »
Used a recoil lug on my Bordon Rimrock in .30 BR
But then maybe I am not overly adventurous.

2
BR Equipment + Components / Re: Action Wrench
« on: March 19, 2019, 02:37:29 PM »
Action wrench is sold.

Thanks

3
BR Equipment + Components / Action Wrench
« on: March 19, 2019, 10:38:37 AM »
For sale
Action Wrench, Bat 2 lug
$ 75.00 shipped

4
OK, like it or not you are likely going to be in the neck turning business. Luck.
Phil

5
What method of turning do you use?
A case holder in a drill works fine.
I turn a hundred in a batch, doesn't take long.
Leave your neck turners set for each caliber,
not as much work setting up that way.
Phil

6
Centerfire Discussions / Re: Borden Rimrock BRM?
« on: December 14, 2018, 08:30:10 PM »
The PPC is glued and screwed, the BR uses a recoil lug forget which brand.

7
Centerfire Discussions / Re: Borden Rimrock BRM?
« on: December 12, 2018, 06:15:02 PM »
I have two Borden Rimrocks both in the BR version ( short )
One in 6PPC for short range benchrest competition, the other in 6BR for long range competition.
They are .308 bolt face and work very well with either 6PPC or .308 case heads.

Phil

8
Going to make you pee in a bottle Rick.

9
Club Events / Re: IBS Nationals - Weikert
« on: August 20, 2018, 06:19:48 AM »
Good shooting Hugh.

10
Paul, great pics, thanks.

11
Centerfire Discussions / Re: remembering equipemnt
« on: August 02, 2018, 09:03:48 PM »
After the last match in Kenora you won’t get mutch  help from me.

12
Centerfire Discussions / Re: remembering equipemnt
« on: August 02, 2018, 03:34:07 PM »
Hey McD,
             Ask Dwayne, he has a
list for his lists , including the #
Of chocolate bars.

Phil

13
BRSC - Benchrest Shooters Canada / Mission B.c.
« on: August 01, 2018, 06:22:01 PM »
This is for the Alberta guys travelling to Mission.
If you are going # 1 HWY. Leave early. ( two hours )
Road construction and slow drivers , heavy traffic.

Phil

14
Off Topic / Re: Greetings From Ottawa
« on: July 24, 2018, 02:54:53 PM »
Hello and welcome Ottawa, I'm from the other side of Ontario.

Phil

15
Centerfire Discussions / Re: High pressure signs
« on: April 19, 2018, 06:21:46 AM »
I start at jam length and work my way back.
Usually end up back at jam length for consistency.
Go figure.

16
Centerfire Discussions / Re: High pressure signs
« on: April 18, 2018, 08:40:48 PM »
Start with a new piece of brass, say three fire forming shots on it. Increase the load by 1/2 gr. at a time.
If the primer pocket gets loose, back off. Also stiff bolt lift is not good thing, back off.
What powder and load are you running now ? Good bench guns tend to run hotter than book loads.
Nothing wrong with being cautious, it's a great safety feature.

17
What twist and barrel profile ?

18
Centerfire Discussions / Re: Neck size diameter
« on: February 15, 2018, 06:51:38 AM »
26.9 gr. of what ?  This sounds really light, and may account for the sooty cases.
Try going up in charge weight to the next node, this will probably expand the cases
enough to seal the chamber. Work up to it.

19
Centerfire Discussions / Re: Neck size diameter
« on: January 31, 2018, 12:31:26 PM »
HI,
   Turn your necks to achieve a clearance of 1 1/2" to 2 thou. under your chamber neck dimension.
   This should be measured by seating the bullet of your choice in the turned neck and then measuring
   the outside diameter of the  neck where the bullet base sits.

Phil

20
See you there Dan.

Pages: [1] 2 3 ... 5
SMF spam blocked by CleanTalk