21
Centerfire Discussions / Re: Borden Rimrock BRM?
« on: December 14, 2018, 08:30:10 PM »
The PPC is glued and screwed, the BR uses a recoil lug forget which brand.
Where Precision and Accuracy Meet
News:
NEW USERS MUST CONTACT RICKPOLLOCK@SHAW.CA BEFORE LISTING ITEMS FOR SALE
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
22
Centerfire Discussions / Re: Borden Rimrock BRM?
« on: December 12, 2018, 06:15:02 PM »
I have two Borden Rimrocks both in the BR version ( short )
One in 6PPC for short range benchrest competition, the other in 6BR for long range competition.
They are .308 bolt face and work very well with either 6PPC or .308 case heads.
Phil
One in 6PPC for short range benchrest competition, the other in 6BR for long range competition.
They are .308 bolt face and work very well with either 6PPC or .308 case heads.
Phil
23
BRSC - Benchrest Shooters Canada / Re: Rosebud - AB Provincials 100/200 yd (lv,hv) Sept 1/2 2018
« on: September 06, 2018, 08:39:12 PM »
Going to make you pee in a bottle Rick.
24
Club Events / Re: IBS Nationals - Weikert
« on: August 20, 2018, 06:19:48 AM »
Good shooting Hugh.
25
BRSC - Benchrest Shooters Canada / Re: Mission - 2018 BRSC Nationals Results
« on: August 13, 2018, 06:15:47 AM »
Paul, great pics, thanks.
26
Centerfire Discussions / Re: remembering equipemnt
« on: August 02, 2018, 09:03:48 PM »
After the last match in Kenora you won’t get mutch help from me.
27
Centerfire Discussions / Re: remembering equipemnt
« on: August 02, 2018, 03:34:07 PM »
Hey McD,
Ask Dwayne, he has a
list for his lists , including the #
Of chocolate bars.
Phil
Ask Dwayne, he has a
list for his lists , including the #
Of chocolate bars.
Phil
28
BRSC - Benchrest Shooters Canada / Mission B.c.
« on: August 01, 2018, 06:22:01 PM »
This is for the Alberta guys travelling to Mission.
If you are going # 1 HWY. Leave early. ( two hours )
Road construction and slow drivers , heavy traffic.
Phil
If you are going # 1 HWY. Leave early. ( two hours )
Road construction and slow drivers , heavy traffic.
Phil
29
Off Topic / Re: Greetings From Ottawa
« on: July 24, 2018, 02:54:53 PM »
Hello and welcome Ottawa, I'm from the other side of Ontario.
Phil
Phil
30
Centerfire Discussions / Re: High pressure signs
« on: April 19, 2018, 06:21:46 AM »
I start at jam length and work my way back.
Usually end up back at jam length for consistency.
Go figure.
Usually end up back at jam length for consistency.
Go figure.
31
Centerfire Discussions / Re: High pressure signs
« on: April 18, 2018, 08:40:48 PM »
Start with a new piece of brass, say three fire forming shots on it. Increase the load by 1/2 gr. at a time.
If the primer pocket gets loose, back off. Also stiff bolt lift is not good thing, back off.
What powder and load are you running now ? Good bench guns tend to run hotter than book loads.
Nothing wrong with being cautious, it's a great safety feature.
If the primer pocket gets loose, back off. Also stiff bolt lift is not good thing, back off.
What powder and load are you running now ? Good bench guns tend to run hotter than book loads.
Nothing wrong with being cautious, it's a great safety feature.
32
BR Equipment + Components / Re: ISO Rem700 SS recoil lug .// 6mm blank or BR barrel/ jewel to fit same 700
« on: February 28, 2018, 08:31:43 PM »
What twist and barrel profile ?
33
Centerfire Discussions / Re: Neck size diameter
« on: February 15, 2018, 06:51:38 AM »
26.9 gr. of what ? This sounds really light, and may account for the sooty cases.
Try going up in charge weight to the next node, this will probably expand the cases
enough to seal the chamber. Work up to it.
Try going up in charge weight to the next node, this will probably expand the cases
enough to seal the chamber. Work up to it.
34
Centerfire Discussions / Re: Neck size diameter
« on: January 31, 2018, 12:31:26 PM »
HI,
Turn your necks to achieve a clearance of 1 1/2" to 2 thou. under your chamber neck dimension.
This should be measured by seating the bullet of your choice in the turned neck and then measuring
the outside diameter of the neck where the bullet base sits.
Phil
Turn your necks to achieve a clearance of 1 1/2" to 2 thou. under your chamber neck dimension.
This should be measured by seating the bullet of your choice in the turned neck and then measuring
the outside diameter of the neck where the bullet base sits.
Phil
35
Club Events / Re: Mission & District Rod & Gun Club Center Fire Benchrest Schedule 2018
« on: January 08, 2018, 09:15:18 PM »
See you there Dan.
36
Club Events / Re: Canadians Have a Great Showing at IBS 2017 Group Nationals in Holton
« on: August 21, 2017, 11:05:44 AM »
And darn good shooting by Hugh Williamson.
Way to go Hugh.
Way to go Hugh.
37
BRSC - Benchrest Shooters Canada / Re: BRSC National Championships July 1/2 2017 - Selkirk, MB
« on: July 05, 2017, 08:03:46 AM »
Selkirk ran a great shoot, and even the shooters helped out where needed.
Chelsy, thank you for running targets and scoring, great job.
Phil
Chelsy, thank you for running targets and scoring, great job.
Phil
38
BRSC - Benchrest Shooters Canada / Re: BRSC National Championships July 1/2 2017 - Selkirk, MB
« on: June 27, 2017, 08:18:43 AM »
Will be there on Friday Rick, maybe not ready but I will be there.
Phil
Phil
40
Photo And Video Gallery / Re: Pumpkin Neck Turner
« on: April 16, 2016, 10:49:54 AM »
I use the PMA no issues, works well.
SMF spam blocked by CleanTalk